Vortex86MX+

DM&P Semiconductor Inc. se enorgullece de ofrecer el microprocesador basado en MPU Vortex86MX+ x86. El Vortex86MX+ es un Sistema-en-Chip (SoC) compatible con x86 fabricado con un proceso de 90nm y diseñado para consumir menos de 1 vatio de electricidad. Integra múltiples funciones como múltiples puertos de E/S (RS-232, Paralelo, USB y GPIO), BIOS, temporizador Watch Dog, gestión de energía, contador MTBF, LoC (LAN on Chip), JTAG y GPU, todo en un solo chip BGA.

Dentro de su paquete BGA de 720 pines, los paquetes Vortex86MX+ contienen un “write through” cache L1 de 32kb y nivel de asociatividad “4-way”, un “write through/ write back” cache L2 de 256KB y nivel de asociatividad “4-way”, PCI rev. 2.1 Interfaz de bus de 32 bits a 33 MHz, DDR2, controlador de ROM, IPC (controladores de periféricos internos con DMA y temporizador / contador de interrupciones incluidos), Fast Ethernet MAC, FIFO UART y USB 2.0 Host y controladores IDE. Con soporte para DOS, Windows, Linux y otros RTOS, proporciona una solución ideal para los sistemas embebidos y productos de comunicaciones como thin clients, routers NAT, gateways domésticos, puntos de acceso y Tablet PCs.

Características

x86 32-Bit Processor Core

6 Stage Pipe-line

Embedded I/D Separated L1 Cache

16K I-Cache, 16K D-Cache

SDRAM/DDR2 Control Interface

Support DLL for clock phase auto-adjustion

IDE Controller

Support 2 Channels Ultra-DMA 100 (Disk x 4)

LPC (Low Pin Count) Bus Interface

Support 2 Programmable Registers to Decode LPC Addresses

MAC Controller

Supports 1

PCI Controller Interface

Supports Up to 3 Sets of PCI Master Devices
3.3V I/O

ISA Bus Interface

AT Clock Programmable
8/16 Bit ISA Device With Zero-Wait-State
Generate Refresh Signals to ISA Interface During DRAM Refresh Cycle

DMA Controller

Interrupt Controller

Counter/Timers

Supports 2 of 8254 Timer Controllers
Timer Output is 5V Tolerance I/O on 2nd Timer

Real Time Clock (Internal/External)

Below 2uA Power Consumption on Internal Mode (Estimation Value)

FIFO UART 5 x Ports (COM Ports)

Compatible with 16C550/16C552
Default Internal Pull Up
Supports the Programmable Baud Rate Generator with Data Rate from 50kbps to 115.2kbps
The Characters Options are Programmed for 1, 1.5 or 2 stop bits; even, odd or no parity; 5-8 data bits
Supports TXD_EN Signal on COM1/COM2
Port 80H Output Data could be sent to COM1 by software programming.

General Chip Selector

2 Sets of Extended Chip Selector
I/O MAP or Memory MAP could be configurable
I/O Addressing: From 2 byte to 64K byte
Memory Address: From 512 byte to 4G Byte

General Programmable I/O

Support 40 Dedicated Programmable I/O Pins
Each GPIO Pin Can Be Individually Configured to be an Input/Output Pin

USB 2.0 Host

4 x USB Ports
Support HS, FS, and LS

PS/2 Support

Keyboard and Mouse
Compatible with 8042 Controller

Speaker

Output

Embedded 256KB Flash

JTAG Support

Interface Support for S.W Debugging

Input Clock

14.318MHz
32.768KHz

Output Clock

24MHz
25MHz

Operating Voltage Range

Core voltage: 1.2 V ~ 1.4V
I/O voltage: 1.8V ± 5% , 3.3 V ± 10 %

Operating Temperature

-40 – 85 Degrees Celius

Package Type

27 x 27, 581 Balls 8GA

Descargas

CPU Benchmark Report
Are the COM ports in Vortex86DX2 all 16C550 compatible?
Can the GPIO in Vortex86DX2 be programmed individually?
Do all internal IO mapped peripherals decode all 16 address lines for IO cycles?
How can I use the internal Ethernet with Vortex86DX2?
How to use external RTC instead of internal RTC?
RS485 transmission trouble

What Operating Systems Supports Vortex86DX2?

Is there Boot ROM function for LAN in default AMI BIOS?
Can I boot with DOS from USB ?
AMI BIOS checkpoint list
AMI BIOS Reference Manual